BMW E36 engine reliability guide

John Avis by | February 8, 2013 | E36

When you are shopping for a car as old as the E36 generation 3 series, it makes sense to choose the model that will be the most reliable and require the least maintenance. Here's a run down on the pros and cons of most of the engines available (in Australia).
When you are shopping for a car as old as the E36 generation 3 series, it makes sense to choose the model that will be the most reliable and require the least maintenance. Here's a run down on the pros and cons of most of the engines available (in Australia).

M40 - 4 cylinder 1.8 litre

Not one of BMW's best engines. It has a timing belt which needs regular maintenance. Suffers from top end wear.

M42 - 4 cylinder 1.8 litre

Originally introduced late in the previous E30 generation life cycle, this engine carried over the E36 coupe with a few changes. Uses a double row timing chain that lasts well. Valve gear can get a little rattly but is no cause for alarm.

M43 - 4 cylinder 1.8 litre

The replacement for the M40. Fitted with a timing chain. This seems to be a reliable engine, for the most part.

M44 - 4 cylinder 1.9 litre

The replacement for the M42. Still with a timing chain. Valve gear improved with roller rockers. Fitted with some plastic coolant pipes which disintegrate with age. One is at the back of the engine which is difficult to replace without the engine or transmission out (replace it if regardless if you are doing this type of major work). [Edit: I have since been told this pipe can be replaced by only removing the valve cover]

The M44 also suffers from a leaking oil filter housing gasket. If you are leaving a lot of oil on the ground where you park then this is the most likely cause. Fortunately they are fairly easily to replace.

M50 - 6 cylinder 2.0 litre and 2.5 litre

Fitted with timing chain. Later models had variable valve timing for inlet valves which can be problematic but early models (1991 and 1992) didn't. Strong iron block with aluminium head.

M52 - 6 cylinder 2.5 litre and 2.8 litre

Replacement for the M50. Fitted with timing chain and variable valve timing on both inlet and exhaust valves. Aluminium block which means that it doesn't like overheating and head gasket replacement can result in stripped threads. Some oil consumption problems due to either Nikasil cylinder linings, bore glazing or oil separator valve. Many engine blocks were replaced under warranty.

Like most of BMW's VANOS equipped engines, the M52 can suffer problems in this system.

Summary

All BMW engines have a reputation for needing regular cooling system maintenance. Personally in more than a decade of BMW ownership, and around 7 different cars, I have only had to replace one water pump. However, I have had to replace the thermostat in almost every BMW I have owned. I have never had a problem with overheating.

In my opinion the best choices are M42 or M44 for 4 cylinder models, or the M50 for 6 cylinder models.

If you do want a 318i then I would strongly recommend you avoid the earlier M40 powered cars and find a later model with the M43 engine.

Related Posts

E36

Japanese BMW M44 engine document

by John Avis | September 9, 2019

I found this Japanese document, presumably from BMW, that covers the M44 engine.


E36 E30

(De)Evolution of the BMW 3 series ventilation and heating systems

by John Avis | January 28, 2016

I have a strong disliking of the climate control system in my BMW E36, but in my previous E30, the controls for ventilation, heating and air conditioning were near perfect.


E36

Top 3 performance modifications for a street driven BMW E36

by John Avis | January 23, 2015

If you are looking for the best modifications you can do to your BMW 3 series from 1991 to 1997, here's my top 3 list for the modifications that you will notice the most improvement.

Comments

chisa

by chisa | December 29, 2019

can i use the bmw e36 318i engine (soch) in place of the bmw e46 318i?
advise

Reply

Leave a Reply
John Avis

by John Avis | December 30, 2019

You might be best asking this in one of the many BMW forums. I'm sure it is possible but not sure what needs to be swapped. In Australia it would be illegal as you can't fit an engine from an older car.

Reply

Tags

Subscribe

Get the latest posts delivered to your inbox.